Part No. 4801-5117 Rev. 8-01 Owners Manual Farm Hand SCS Farm Hand SCSFarm Hand SCS Farm Hand SCS w/BackFarm Hand SCS w/Back--UpUp Hired Hand, Inc
Part No. 4801-5117 Rev. 8-01 Farm Hand SCS 8 To Back-up Relay hand the Fail-Safe relay strip would close each of the relays in the strip resultin
Part No. 4801-5117 Rev. 8-01 Farm Hand SCS 9 12. Day-to-Day Back-Up Operating Instructions 12.1 Toggle Sequence of Mode Button Continuously p
Part No. 4801-5117 Rev. 8-01 Farm Hand SCS 10 2. Press the ”+” and ”–“ buttons to enter the value of the High Limit. 3. Setting Complete. Set
Part No. 4801-5117 Rev. 8-01 Farm Hand SCS 11 1. Place a thermometer inside the house at the location of each sensor. Allow a few minutes for
Part No. 4801-5117 Rev. 8-01 Farm Hand SCS 12 17. Wiring Diagrams Warning! Before connecting power to the machine, be sure to place the jumpers
Part No. 4801-5117 Rev. 8-01 Farm Hand SCS 13 17.2 Setting the Back-Up Board Jumpers, Sensors and Alarm Connections
Part No. 4801-5117 Rev. 8-01 Farm Hand SCS 14 17.3 16 Stage SCS™ Panel Back-Up Jumper Posi
Part No. 4801-5117 Rev. 8-01 Farm Hand SCS 15 17.4 Setting the Local Network Address DIP Switch Settings SCS™ Stage Addr
Part No. 4801-5117 Rev. 8-01 Farm Hand SCS 16 17.5 SCS™ Local Net and Back-Up Interconnection Diagram
Part No. 4801-5117 Rev. 8-01 Farm Hand SCS 17 17.6 SCS™ Connections to the Power Supply HOT 120V NEUT 240V
Part No. 4801-5117 Rev. 8-01 Farm Hand SCS Table of Contents Table of Contents Section Title Page 1. Ratings and S
Part No. 4801-5117 Rev. 8-01 Farm Hand SCS 18 17.7 SCS™ Connections to the Curtain Machine Top Left of SCS Panel POWER TRAK HO
Part No. 4801-5117 Rev. 8-01 Farm Hand SCS 19 17.8 Connecting Power from Breaker to a Heat Stage or Cool Stage All wiring must meet N.E.C. and
Part No. 4801-5117 Rev. 8-01 Farm Hand SCS 20 Note: In step 2, it very important to remove electrical power from the circuits connected to the re
Part No. 4801-5117 Rev. 8-01 Farm Hand SCS 21 19. Temperature vs. Sensor Resistance Table The following chart gives the resistance when measur
Part No. 4801-5117 Rev. 8-01 Farm Hand SCS 22 20. Error Codes If your controller is displaying an “E1” or “E2”, etc. the controller has recorde
Part No. 4801-5117 Rev. 8-01 Farm Hand SCS 23 21. SCS™ Program Label Programming P 1-9 Stage Programming P1 = Metric Units P2 = Alarm On Back
Part No. 4801-5117 Rev. 8-01 Farm Hand SCS 1 1. Ratings and Specifications • 115/230 Volts (Depending on switch position.) • 50/60 Hz. • 1 h
Part No. 4801-5117 Rev. 8-01 Farm Hand SCS 2 4. Introduction to the SCS™(Smart Contactor System) The SCS™ (Smart Contactor System), in its simp
Part No. 4801-5117 Rev. 8-01 Farm Hand SCS 3 5. Farm Hand SCS Panels Farm Hand SCS 8 Sta
Part No. 4801-5117 Rev. 8-01 Farm Hand SCS 4 AUTO OFF ON Stage Control Switch (3 position) Stage Status Indicators Write in the Name you choose
Part No. 4801-5117 Rev. 8-01 Farm Hand SCS 5 6. Connecting Multiple SCS™ Panels to a Master Controller Up to 128 SCS™ stages can be controlled f
Part No. 4801-5117 Rev. 8-01 Farm Hand SCS 6 DIP Switch Settings SCS™ Stage Address Assignment No. 1 No. 2 No. 3 ON ON ON 1 –16 OFF ON ON
Part No. 4801-5117 Rev. 8-01 Farm Hand SCS 7 it warms the building at least 2°. The same is true if the temperature goes above the High Limit ho
Commentaires sur ces manuels