Hired-hand Emergency Back-Up and Alarms: S-3 Power Switch Upg Manuel d'utilisateur télécharger pdf

INSTALLATION INSTRUCTIONS

S-3 Power Switch Upgrade Kit

HIRED-HAND MFG., INC. • 1733 County Rd 68 • Bremen, Alabama 35033 · Phone 256-287-1000 • Fax 256-287-2000

Part No. 4802-5104 rev 9-05 Page 1 of 4

WARNING!

Only qualified electrician personnel familiar

with the construction and operation of this

equipment and the hazards involved should

install and/or service this equipment. Read

and understand all instructions and diagrams

before proceeding. Failure to observe this

precaution could result in equipment damage,

severe bodily injury, or loss of life.

/KIT S3 Power Switch upgrade 6450-5092

Tools Required

Small flat-head screwdriver Tape Measure

Drill ½” Drill Bit

5/8” Wrench

DESCRIPTION

The S-3 Power Switch Upgrade Kit allows previous

models of the Secondary Sensing System without a

power switch to be easily modified to include an

ON/OFF power switch. When common power

connections are used for multiple controllers, the S-3

ON/OFF power switch allows independent power

control. The kit includes the switch, switch spacer nut,

switch boot cover, ON/OFF label, and quick-connect

wire assemblies to connect to existing wire assemblies.

When the kit is received, check for shipping damage or

missing parts. Refer to Table A for kit content.

Power Switch Hole Placement

The Power Switch should be located on the hinge side of

the enclosure. The hole must be placed low enough near

the bottom to have clearance from the battery support

bracket.

(1) Disconnect all AC electrical power from the

Secondary Sensing System controller.

(2) Disconnect the BAT+ Red wire at the Battery

terminal.

(3) Use the measurements supplied in Figure 2 and

mark the drill location on the hinge side of the

enclosure.

(4) Ensure that all wires and other obstructions are

cleared inside the enclosure near the drilling

location.

(5) Use a ½” drill bit to drill the hole for mounting

the power switch.

(6) Apply the Power ON/OFF label to the outside of

the enclosure with the label cross-marks over the

center of the drilled hole.

(7) Cut a hole in the label around the cross-marks to

match the drilled hole size.

Figure 1: S-3 ON/OFF Switch Installed

Bottom

Door Hinge Side

Label

Switch Boot

& Switch

WARNING!

Ensure that the Electrical Power Sources

are OFF during installation / wiring.

Figure 2: Hole Location

Door

Hinge

1 2 3 4

Résumé du contenu

Page 1 - INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS S-3 Power Switch Upgrade Kit HIRED-HAND MFG., INC. • 1733 County Rd 68 • Bremen, Alabama 35033 · Phone 256-287-1000 • Fax

Page 2 - WARNING!

HIRED-HAND MFG., INC. • 1733 County Rd 68 • Bremen, Alabama 35033 · Phone 256-287-1000 • Fax 256-287-2000 Part No. 4802-5104 rev 9-05 Page 2 of 4 Po

Page 3 - Figure 4 – Wire Connections

HIRED-HAND MFG., INC. • 1733 County Rd 68 • Bremen, Alabama 35033 · Phone 256-287-1000 • Fax 256-287-2000 Part No. 4802-5104 rev 9-05 Page 3 of 4

Page 4

HIRED-HAND MFG., INC. • 1733 County Rd 68 • Bremen, Alabama 35033 · Phone 256-287-1000 • Fax 256-287-2000 Part No. 4802-5104 rev 9-05 Page 4 of 4

Commentaires sur ces manuels

Pas de commentaire

Hired-hand Emergency Back-Up and Alarms: S-3 Power Switch Upg Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Hired-hand Emergency Back-Up and Alarms: S-3 Power Switch Upg. Hired-Hand Emergency Back-Up and Alarms: S-3 Power Switch Upgrade Kit User Manual [en] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Hired-hand Emergency Back-Up and Alarms: S-3 Power Switch Upg